Fosmon Hybo Snap case for the Moto G
I mentioned this case in the Moto G case list thread, it arrived today: giving a more detailed review since people requested it :)
Caveat: On an annoying note, I got charged an extra .13 by the USPS for inadequate shipping by the seller. Filing a complaint with Amazon -- it's a small amount of money, but sellers should not be advertising free shipping if they're going to do that sort of thing.
Cost: .50 + additional .13 for USPS charged shipping. Seller has since upped the price to .95 on Amazon & Ebay.
Onto the case itself:
- Two-piece TPU / polycarbonate shell case, with covered ports and a built-in screen protector
- Put on the TPU part first, then push polycarbonate part on top, then click the TPU flaps in place all around the phone. Extremely easy to both insert and remove the phone into the case.
The case itself does not feel cheap for such an inexpensive case. Both parts fit together very well -- the TPU piece snaps into the hard back and I didn't notice any large gaps or seams or other signs of shoddy workmanship aside from 1 point that I'll get to in a moment.
The TPU is rigid but pliable (not the stiffest TPU I've seen, but somewhat firmer than the rubber band around the official moto G grip shell). It's close to true black (not dark grey) and the sides have a nice texture for good grippiness, with a satin finish overall.
The polycarbonate (hard plastic) back is very matte and has nearly the same texture as the official Moto G backs, albeit a little more "velvety" (smoother feeling, hard to explain). It looks like it will also be a fingerprint magnet as well.
Both the headphone and microUSB ports have covers. The headphone cover is snapped in very securely, but the microUSB cover does not and sits slightly ajar (I'm not sure how it will hold up to repeated opening/closing). There are two small holes on the top and bottom of the case to allow for the two mics (regular mic + (noise reduction?) mic on top).
The back cover raises the camera/flash/logo/speaker off a table surface by around 1mm -- sufficient to prevent scratching, imho.
The buttons remain responsive with the TPU covering them --- in fact I'd say they're more sensitive because they are raised instead of recessed, this could be a plus or minus to you. Hides the jiggliness of my power button.
The built-in screen protector is the part I feel the most ambivalent about. I'm not a fan of built-in protectors in cases normally. This one is typical in that it sits slightly above the surface of the phone (not an adhesive type protector). You will hear a slight "click" when you're tapping on the screen and I find my finger dragging more on the screen. Responsiveness seems to remain the same, however. I had no problem firing off several texts and an email, or navigating through the phone itself. Clarity and color remains the same (included a photo of the phone screen on with the screen protector as a visual) --- the "greenish" tint in the photo is actually just a protective film you remove from the protector prior to installing the case. Does not interfere with the proximity sensor.
Conclusion:
Overall for a case under it seems like a good deal. I'm still annoyed with the shipping issue, but the case itself is pretty solid --- it fits the phone exactly, flaps snap in as they're supposed to with the exception of the microUSB cover. I compared the thickness of the TPU around the sides of the phone with the Moto G Grip Shell, and it's definitely quite a bit thicker. While this adds more bulk to the phone, it also increases the protectiveness. The thinnest parts of the TPU are covered with the hard plastic and gives more added protection.
I'll be keeping my phone in this case for now and will update this review if anything else comes up.
Photos: (I kept my other cases, the Moto Grip Shell and the Rearth Ringke Slim case, for size & color comparison in some of them)
I hope this review is useful for people who are looking for an inexpensive case for their Moto G :good:
I mentioned this case in the Moto G case list thread, it arrived today: giving a more detailed review since people requested it :)
Caveat: On an annoying note, I got charged an extra .13 by the USPS for inadequate shipping by the seller. Filing a complaint with Amazon -- it's a small amount of money, but sellers should not be advertising free shipping if they're going to do that sort of thing.
Cost: .50 + additional .13 for USPS charged shipping. Seller has since upped the price to .95 on Amazon & Ebay.
Onto the case itself:
- Two-piece TPU / polycarbonate shell case, with covered ports and a built-in screen protector
- Put on the TPU part first, then push polycarbonate part on top, then click the TPU flaps in place all around the phone. Extremely easy to both insert and remove the phone into the case.
The case itself does not feel cheap for such an inexpensive case. Both parts fit together very well -- the TPU piece snaps into the hard back and I didn't notice any large gaps or seams or other signs of shoddy workmanship aside from 1 point that I'll get to in a moment.
The TPU is rigid but pliable (not the stiffest TPU I've seen, but somewhat firmer than the rubber band around the official moto G grip shell). It's close to true black (not dark grey) and the sides have a nice texture for good grippiness, with a satin finish overall.
The polycarbonate (hard plastic) back is very matte and has nearly the same texture as the official Moto G backs, albeit a little more "velvety" (smoother feeling, hard to explain). It looks like it will also be a fingerprint magnet as well.
Both the headphone and microUSB ports have covers. The headphone cover is snapped in very securely, but the microUSB cover does not and sits slightly ajar (I'm not sure how it will hold up to repeated opening/closing). There are two small holes on the top and bottom of the case to allow for the two mics (regular mic + (noise reduction?) mic on top).
The back cover raises the camera/flash/logo/speaker off a table surface by around 1mm -- sufficient to prevent scratching, imho.
The buttons remain responsive with the TPU covering them --- in fact I'd say they're more sensitive because they are raised instead of recessed, this could be a plus or minus to you. Hides the jiggliness of my power button.
The built-in screen protector is the part I feel the most ambivalent about. I'm not a fan of built-in protectors in cases normally. This one is typical in that it sits slightly above the surface of the phone (not an adhesive type protector). You will hear a slight "click" when you're tapping on the screen and I find my finger dragging more on the screen. Responsiveness seems to remain the same, however. I had no problem firing off several texts and an email, or navigating through the phone itself. Clarity and color remains the same (included a photo of the phone screen on with the screen protector as a visual) --- the "greenish" tint in the photo is actually just a protective film you remove from the protector prior to installing the case. Does not interfere with the proximity sensor.
Conclusion:
Overall for a case under it seems like a good deal. I'm still annoyed with the shipping issue, but the case itself is pretty solid --- it fits the phone exactly, flaps snap in as they're supposed to with the exception of the microUSB cover. I compared the thickness of the TPU around the sides of the phone with the Moto G Grip Shell, and it's definitely quite a bit thicker. While this adds more bulk to the phone, it also increases the protectiveness. The thinnest parts of the TPU are covered with the hard plastic and gives more added protection.
I'll be keeping my phone in this case for now and will update this review if anything else comes up.
Photos: (I kept my other cases, the Moto Grip Shell and the Rearth Ringke Slim case, for size & color comparison in some of them)
I hope this review is useful for people who are looking for an inexpensive case for their Moto G :good:
Aucun commentaire:
Enregistrer un commentaire